Haga clic aquí para español→
Book a Visit Call Text

Stuck down in the shallows, or stuck up at the ramp.

Jack Plate
Not Moving?

On the flats of Pine Island Sound and the back bays from Estero to the Ten Thousand Islands, the jack plate is how a skiff gets in and out of skinny water. When it stops moving, the boat is stuck at whatever height it quit. Most of the time it is electrical, and most of the time it is fixed at the dock.

Book a $250 Diagnostic Visit (239) 834-8532 Text Us The Boat

What It Usually Is

Nothing happens, or a click at the pump: a relay, a blown fuse or breaker, a corroded connector at the pump or the switch, or a bad switch at the helm. The pump sits in the splash well with the salt, and its connections go first.

The pump hums but the plate does not move: low hydraulic fluid, air in the system from a leak, a failing pump, or a ram seized with corrosion. Fluid weeping down the ram or the hoses is the usual clue.

Moves one way only: a solenoid valve stuck, one relay out of the pair, or a switch wired for one direction. Easy to confirm, usually easy to fix.

Drifts down under way or will not hold position: an internal seal in the ram or a check valve in the pump letting fluid bypass. The plate creeps and the prop ventilates.

Gauge reads wrong or not at all: the position sender or its wiring, not the plate. Worth fixing because a plate you cannot read gets run at the wrong height.

What To Check Safely

Fuse and breaker — the plate usually has its own; find it and check it first
Listen at the pump — a click means power reaches the relay; a hum means the motor runs; silence means no power
Fluid — look for weeping at the ram, the hoses and the pump reservoir
Connections — green or white crust on the pump connectors and the switch plug
Both switches — if there is a helm switch and a remote or a second switch, try both
Manual position — on some plates a manual release lets you set the height to get home; know where yours is

Keep hands clear of the plate and the engine while anyone is working the switch. It moves with the full weight of the outboard behind it.

When To Stop And Call

If the plate drifts under way, or the engine moves on the transom when it should not, do not run the boat at speed. A plate that will not hold height lets the prop ventilate at the wrong moment, and a loose plate loads the transom bolts. Get it looked at before the next trip. We come to the dock with the fluid, the common pumps, relays and switches, and the tools to bleed the system.

Jack Plate Repair At Your Dock: Pumps, Switches, Rams, Gauges

We test the switch circuit, the relays and the pump's current draw, then the hydraulic side: fluid, the pump and the ram seals, and the hoses. Most jack plate jobs are a relay, a connector, a switch or a fluid-and-seal service done at the dock the same day. Pumps and rams are quoted in writing before they are replaced.

Regular hours (6am–4pm): a $250 diagnostic visit. We come to the boat, find the actual cause, and quote parts and labor before any work starts. After hours, Sundays and holidays: a $295 call-out. Parts, labor and sales tax always show as separate lines on the invoice, so you can see exactly what you paid for.

Want the whole engine looked after, not only this fault? See the Premium Full Service — the complete outboard service, whatever your hour meter says, parts included and one price per engine, and Dock Care for boats that sit between trips.

Service guides: Yamaha oil change · Mercury & Verado oil change · Lower unit service · Fuel filters · The 100 / 300 / 500-hour service explained · Electrical & electronics problems.

Straight Answers

Can you fix my jack plate at the dock, or does the boat need to come off the water?
At the dock or on the lift for almost everything. A ram replacement is easier on a lift or trailer; we tell you which before we come.

What fluid does a jack plate use?
It depends on the maker. Many use the same fluid as the engine's power trim; some specify a hydraulic oil. We bring the right one. The wrong fluid damages the seals.

Why does my jack plate quit after the boat sits?
Corrosion at the connections, the same reason trim motors quit. A few months of salt air on an unused connector is all it takes.

Can you install a jack plate on my skiff?
Yes. Plate selection for the boat and engine, mounting, hydraulics, wiring and a gauge, with the engine re-rigged at the right height. Ask us for a quote.

Do you work on skiffs out of Pine Island, Matlacha and Bokeelia?
Yes. That is jack plate country: St. James City, Bokeelia, Matlacha, Pineland, and the bay boats in Cape Coral, Punta Gorda, Fort Myers Beach, Bonita, Naples, Marco Island and the Ten Thousand Islands.

Is a jack plate the same as power trim?
No. Trim tilts the engine; the jack plate raises and lowers it vertically on the transom. They have separate pumps and switches, though they fail for the same reasons.

Anywhere The Boat Is

Dock, lift, marina, driveway or storage lot — we come to the boat across Southwest Florida:

Jack plates live on the skiffs and bay boats that fish Pine Island Sound, Matlacha Pass, Charlotte Harbor out of Punta Gorda, Estero Bay behind Fort Myers Beach and Bonita, the back bays of Sanibel and Captiva, Naples Bay, Marco Island and the Ten Thousand Islands, and the canals of Cape Coral. We come to the boat where it sits.

Cape CoralFort MyersNorth Fort MyersLehigh AcresFort Myers BeachSanibel & CaptivaPine Island & MatlachaPunta GordaPort CharlotteBoca GrandeBonita SpringsEsteroNaplesMarco IslandLaBelle & Alva

Plate Stuck? Get Back In Skinny Water.

Text us the boat, the plate and what it does. We carry relays, switches, fluid and seals for the common jack plates and come to the dock.

Book a $250 Diagnostic Visit (239) 834-8532 Text Us

Se habla Español · All services →

More boat problems: Boat won't start · Overheating alarm · Lower unit leaking · Won't go into gear · Trim not working · Battery keeps dying · What repairs cost · GPS or chartplotter dead · Boat lights not working · Bilge pump not working · Livewell pump not working · Gauges not working · Outboard not peeing · Outboard alarm going off · Losing power, won't plane · Stalls at idle or in gear · Not charging the battery · Steering stiff or leaking · Prop vibration or spun hub · Water in the fuel · Outboard smoking · Power-Pole & trolling motor · Garmin & electronics installs · Emergency, open now · Yamaha outboard repair · Mercury & Verado repair · Suzuki outboard repair